Glock Pro Forums banner
1 - 8 of 8 Posts

·
Registered
Joined
·
302 Posts
Discussion Starter · #1 · (Edited)
FOUNDI am looking for a Channel Liner, Firing Pin Spring, Trigger Spring & Two Spring Cups..FOUND
I would like to buy a NEW factory G17 recoil spring, & extractor spring.. Plus the factory adjustable sights mini screwdriver
These would all be for use in my 1990 Glock 17L to return it to factory specs.
I may be able to pick a few of these parts up from a couple armourers in the Louisville Area or The Glock Doc at some of the Gunshows in the area..
Thanks
Email Me @ [email protected]
Gary
 

·
Registered
Joined
·
302 Posts
Discussion Starter · #3 · (Edited)
I figured I'd just reply here at the forum..
Thanks for the reply..

The Only Glock Parts I have are in my stash SO FAR are..
2- Factory Slide Release levers
1- Set of plastic sights, Early Pinned front type - marked
1- Breach Block Pin
1- Trigger Pin
1- G19/G23 Trigger Bar Assembly Serrated Target Style
1- G17 Butt Plug
1- G26/27/33 Scherer Butt Plug
2- Factory 5.5lb Connectors
1- Scherer +1 Floorplate G27 G33

That's about it..
I just traded a Glockmeister G19/G23 recoil Rod & a G19 butt plug for a Factory adjustable rear sight & a Hi-Viz for the front of my G17L..
I don't have many Glock items as they all pretty much got sold or traded a while back when I sold my G19, I ended up getting rid of several G19 magazines + a 33rd Glock magazine & two holsters, all that I wish I still had since picking up the G17L & G26..
Thanks!!
Gary

There's three gunshows this weekend that I will attend but the Glock Guy hasn't been at the last few shows..
There's the INDY 1500 coming up were the Glock Doc will be & maybe I can aquire what I need there??

The Three gunshows this weekend are..
Cave City Kentucky - Richey Shows http://www.hoosiergunworks.com/cave_city.html
Lexington kentucky - RK/Kenny Woods Gunshows http://www.rkshows.com/
Salem Indiana - Tri State Gunshows http://www.tri-stategunshows.com/
 

·
Registered
Joined
·
302 Posts
Discussion Starter · #4 ·
Hey I am also interested in picking up a factory rear adjustable sights micro little screw driver..
i know most folks take these off & I've found & installed one on my 17L..
I have a few different micro screw drivers that will fit this sight, Just looking for the factory one to put in the case, If/When I find one..
I'm also looking for a long Tupperware case for a 17L or G24..
I saw one a while back for $15 but hadn't picked the 17L up yet or I'd have been in it..
Thanks!!
 

·
Registered
Joined
·
302 Posts
Discussion Starter · #5 · (Edited)
Today @ Bud's Gun Shop in Lexington KY I found several of the parts I was looking for..

I Still Need a Factory G17 Recoil Spring & Guide Rod Assembly plus the blue extractor Spring for a 9mm G17

I was able to pick up the Firing Pin Spring, Spring Cups x 2, Channel Liner, & Trigger Spring for $14 & some change @ Bud's plus my buddy MM scored his fourth Stainless Ruger Mini 14 GB for $499 + .06% KY sales Tax.. This after walking the RK/Kenny Woods Gunshow for 2 1/2 Hours were we both bought nothing.. Did see my other buddy who I bought my 17L & 26 from plus Mitch the maker of the MIC Holsters @ glocktec.com, These are great holsters for any lenth of Glock..
I was hoping that Bud's would have the factory OWB open bottom Factory Glock Holster that I could use for both the 17L & 26 Glocks For less than $10 NEW..
They did have the recoil spring assembly for $12.99 but I was out of cash & didn't want to put it on my charge card.. I'll find a another new one eventually.. Wish I would have taken an extra $20spot with me to the gunshow..

I have a couple butt plugs & a G2733 Scherer magazine floorplate to trade if anyone has a need for these two items..
The plugs are for the G17 & G26 the floorplate is for a G26/G27/G33
Also saw a G33 today for $380 OTD..
Also still looking for a couple G26 GAP Floorplates or maybe even one..
Thanks!!
Gary/Hk
[email protected]

Here's a picture of the +1 Scherer G2733 Floorplates, One on & One off my G26..

Here's a pic of the Scherer SP2 G26/27/33 Butt Plug
 

·
Registered
Joined
·
302 Posts
Discussion Starter · #7 ·
I'm still in need of Factory G17 Recoil Spring, Extractor Spring, & Striker Spring..
I would also love to have a Factory Adjustable Sights Screwdriver even though I have several ones in a watch repair kit that will work perfectly at the range..
It's been a few months since I bumped this want add..
I guess I can pick them up at one of the gunshows were the Glock Doctor is or stop bye Bud's Gunshop in Lexington the next time I go to the RK Show There..
Thanks!!
[email protected]
 
1 - 8 of 8 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top